Gear oil pump series
High viscosity pump series
Centrifugal pump series
Pump series for other purposes
2CY stainless steel gear pump
2CY stainless steel gear pump is mainly used for conveying lubricating oil in various mechanical equipment with lubrication systems, suitable for conveying lubricating oil with viscosity ranging from 5 to 1500 cst and temperature below 180 ℃. If high temperature is required, please contact our unit and a seal can be used.
Application scope of 2CY stainless steel gear oil pump:
1. Can be used as a transmission and booster pump in oil transportation systems;
2. In industry, it can be used as a lubricating oil pump;
3. Can be used as a fuel pump for delivery, pressurization, and injection in the fuel system;
4. 2CY gear oil pump can be used as a hydraulic pump to provide hydraulic power in hydraulic transmission systems;
Precautions for using 2CY stainless steel gear oil pump:
1. Installation
a. Before installation, it is necessary to check whether the pump has been damaged during transportation, such as whether the motor is damp, whether the dust covers at the pump inlet and outlet are damaged, and whether dirt enters the pump chamber.
b. Before installing the pipeline, the inner wall of the pipeline should be cleaned with clean water or steam. During installation, the weight of the pipeline should be avoided being borne by the pump to avoid affecting the accuracy and lifespan of the pump.
c. The oil pump should be as close as possible to the oil pool; The connection parts of the pipeline must not leak gas or liquid, otherwise it may cause the phenomenon of not being able to absorb liquid.
d. To prevent impurities such as particles from entering the pump, a metal filter should be installed at the suction port.
e. It is recommended to install vacuum and pressure gauges on the inlet and outlet pipelines to monitor the working status of the pump.
f. When the oil pool is deep, the oil suction pipeline is long, or the medium viscosity is high, causing excessive vacuum, the 2CY gear oil pump can thicken the oil inlet pipe by one gear. When the oil suction pipeline is long, a bottom valve should also be installed.
2. Pre work inspection
a. Are the fasteners of the pump secure.
b. Whether the rotation of the driving shaft is uniform and consistent in weight.
c. Is the valve of the inlet and outlet pipeline open.
d. Does the rotation direction of the pump meet the requirements.
e. Before initial use, an appropriate amount of medium should be injected into the pump.
3. Maintenance during work.
a. Note that the readings on the pressure and vacuum gauges of the pump should comply with the technical specifications specified for the pump.
b. When there is abnormal noise or excessive temperature rise during the operation of the pump, the pump should be stopped immediately for inspection.
c. In general, it is not allowed to adjust the protective valve arbitrarily. If adjustment is needed, an instrument should be used for calibration. Make the cut-off pressure of the protective valve 1.5-2 times the rated pressure of the pump.
4. Stop the pump.
a. Cut off the power.
b. Close the inlet and outlet pipeline valves.
Technical parameters of 2CY stainless steel gear pump:
model | flow Q |
speed
n r/min |
Discharge pressure
p Mpa |
Cavitation margin
)r m |
efficiency
η % | electrical machinery | ||
m3/h | L/min | powerKW | model | |||||
2CY-1.08/2.5 | 1.08 | 18 | 1420 | 2.5 | 9.5 | 58 | 2.2 | Y100L1-4 |
2CY-2.1/2.5 | 2.1 | 35 | 1420 | 2.5 | 9.5 | 58 | 3 | Y100L2-4 |
2CY-3/2.5 | 3 | 50 | 1440 | 2.5 | 9.5 | 59 | 4 | Y112M-4 |
2CY-4.2/2.5 | 4.2 | 70 | 1440 | 2.5 | 9.5 | 59 | 5.5 | Y132S-4 |
2CY-7.5/2.5 | 7.5 | 125 | 1440 | 2.5 | 9.5 | 63 | 7.5 | Y132M-4 |
2CY-12/2.5 | 12 | 200 | 1460 | 2.5 | 9.5 | 63 | 15 | Y160L-4 |
Application of gear oil pumps in the petrochemical industry
1**Coolant circulation system: In petroleum processing equipment, a coolant circulation sys ...
2024-09-24
The application of gear oil pump in the petroleum field
Gear oil pump is a common liquid transfer equipment in industry, which achieves liquid suct ...
2024-09-20
Strengthening the stable operation and improving reliability of circular arc gear oil pumps through r
Strengthen the stable operation and improvement of gear oil pump In the practical operation ...
2024-09-13
Solution to vibration of petroleum gear pump
1、 Solution to vibration of gear pump Mechanical vibration of stainless steel oil pumps i ...
2024-09-09